General Specifications

Fader Stroke 100mm
Fader Resolution (+12 to -∞dB) 1024steps
Power Requirements 40W
Power Consumption US/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz
Operating Temperature Range 0℃ ~ 40℃
Storage Temperature Range -20℃ ~ 60℃
Dimensions (W x D x H) 581 x 720 x 156mm (22-7/8" x 28-3/8" x 6-1/8")
Net Weight 17.8kg (39.2lb)
Included Accessories Power cable, Brackets (2), Getting Started Guide

* All level controls are the nominal position. Output impedance of signal generator:150ohms

Control I/O Characteristics

Terminal Format Connector in Console
Network IEEE802.3 (10Base-T/100Base-TX) RJ-45
REMOTE RS-232C D-SUB Connector 9P (Male)

General Specifications

Power Requirements

30W
Power Consumption US/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz
Operating Temperature Range 0℃ ~ 40℃
Storage Temperature Range -20℃ ~ 60℃
Dimensions (W x D x H) 354 x 720 x 161mm (13-7/8" x 28-3/8" x 6-3/8")
Net Weight 10.0kg (22.0lb)
Included Accessories Jog wheel, Power cable, Brackets (2), Getting Started Guide

Electrical Characteristics

All level controls are the nominal position. Output impedance of signal generator:150ohms. 0dBu = 0.775Vrms

Input Output RL Conditions
Frequency Response TO PHONES Phones A or B Phones level control max,
Input level +4dBu(typ),
20Hz-20kHz, ref to the nominal
output level @1kHz
+0.5, -3dB
Total Harmonic Distortion *1 TO PHONES Phones A or B +4dB@20Hz-20kHz, Phones level control max 0.04%
Hum&Noise *2 TO PHONES Phones A or B Residual output noise, Phones level control min -100dBu
Crosstalk@1kHz *3 CH L Phones out CH R - L/R, adjacent inputs -80dB
CH R Phones out CH L -

Analog Input Characteristics

Input Terminals Actual Load Impedance For Use With Nominal GAIN Input level Connector in Console
Nominal Max. before clip
TO PHONES 20KΩ (BAL) 150Ω Lines 0dB +4dBu
(1.23 V)
+30dBu
(24.56 V)
XLR3-31type connectors *4

Analog Output Characteristics

Output Terminals Actual Source Impedance For Use With Nominal Output level Connector in Console
Nominal Max. before clip
PHONES A 100Ω 8Ω Phones 4mW 25mW Stereo Phone Jack (TRS)
(Unbalanced) *5
40Ω Phones 12mW 75mW
PHONES B 100Ω 8Ω Phones 4mW 25mW Stereo Phone Mini Jack (TRS)
(Unbalanced) *5
40Ω Phones 12mW 75mW
TALKBACK OUT 75Ω 600Ω Lines +4dBu
(1.23 V)
+24dBu
(12.3 V)
XLR-3-32 type (Balanced) *4

Control I/O Characteristics

Terminal Format Connector in Console
NETWORK IEEE802.3 (10Base-T/100Base-TX) RJ-45
REMOTE RS-232C D-SUB Connector 9P (Male)

Appendix
*1. Total Harmonic Distortion is measured with 80kHz LPF.
*2. Hum & Noise are measured with A-weighting filter and 30kHz LPF.
*3. Crosstalk is measured with a -30dB/octave filter @22kHz.
*4. XLR-3-31 and XLR-3-32 type connectors are balanced.(1=GND, 2=HOT, 3=COLD)
*5. PHONES stereo phone jack is unbalanced. (Tip=LEFT, Ring=RIGHT, Sleeve=GND)

General Specifications

Sampling Frequency Internal 44.1kHz/48kHz/88.2kHz/96kHz/176.4kHz/192kHz
External 44.1kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
48kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
88.2kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
96kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
176.4kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
192kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
Frequency Response ±0.5dB, 20Hz-20kHz,ref to the nominal output level @1kHz, Input&Output Gain:0dB, Input level +4dBu(typ)
THD+N *1 Less than 0.005%, input to output, GAIN:0dB
Dynamic Range 120dB typ.,ADC
120dB typ.,DAC
Crosstalk@1kHz -100dB, CH1-16 , adjacent inputs
Power Requirements (wattage) NUAGE I/O 16D: 51W
NUAGE I/O 16A: 51W
NUAGE I/O 8A8D: 51W
Power Requirements
(voltage and hertz)
US/Canada: 120V 60Hz
Japan: 100V 50/60Hz
China: 110-240V 50/60Hz
Korea: 220V 60Hz
Other: 110-240V 50/60Hz
Dimensions (W x D x H) 480 x 369 x 88 mm (18-7/8" x 14-1/2" x 3-1/2")
Net Weight NUAGE I/O 16D: 6.4kg(14.1lb)
NUAGE I/O 16A: 6.7kg(14.1lb)
NUAGE I/O 8A8D: 6.7kg(14.8lb)
Included Accessories Power cable, Ferrite core, Ruber stoppers (4), Operation Manual

*1 These characteristics are measured with A-weighting filter and/or 30kHz LPF.

Analog Input Characteristics

Input Terminal Actual Load
Impedance
For Use With
Nominal
GAIN Input level Connector in Console
Nominal Max.before clip
ANALOG INPUT 20kΩ (BAL) 150Ω Lines 0dB +4dBu (1.23 V) +24dBu (12.28V) D-SUB Connector 25P (Female)
+12dB -10dBV (0.32 V) +10dBV (3.16V)
10kΩ (UNBAL) 600Ω Lines 0dB +4dBu (1.23 V) +24dBu (12.28V) D-SUB Connector 25P (Female)
+12 dB -10dBV (0.32 V +10dBV (3.16V)

Analog Output Characteristics

Output Terminal Actual Source Impedance For Use With
Nominal
GAIN SW Output level Connector in Console
Nominal Max.before clip
ANALOG OUTPUT 75Ω(BAL) 10kΩ Lines 0dB +4dBu (1.23 V) +24dBu (12.28V) D-SUB Connector 25P (Female)
-6dB +18dBu (6.16 V)

Digital I/O Characteristics

Terminal Format Data length Level Connector in Console
AES/EBU AES/EBU Professional use 24bit RS422 D-SUB Connector 25P (Female)
Primary/Secondary Dante 24bit 1000Base-T RJ-45 x 2
Cascade - 32bit LVDS *2 RJ-45 x 2

Control I/O Characteristics

Terminal Level Connector in Console
WORD CLOCK IN TTL/75Ω terminated BNC Connector
OUT TTL/75Ω BNC Connector
System Link Out 1.0±0.2Vp-p/75Ω *3 BNC Connector

*2. Hi Speed CML
*3. AES-3id

General Specifications

PCI Express card Compatible with PCI Express x4 slots v1.0 and above
Audio channels 256 channels (128 in/128 out @ 96 kHz or less)
128 channels (64 in/64 out @ 176.4 kHz or more)
Supported Sample Rates 44.1, 48, 88.2, 96, 176.4, and 192kHz
Pull-up/Pull-down +4.1667, +0.1, -0.1, and - 4.0 %
Sample bit-depth 24 bit
Dante Network interface Gigabit (1000Mbps; 1Gbps) Ethernet RJ45 port x2